135compact.com       110 cartridge ultra compact cameras       How to replace a Kodak K or 7R31 type K battery (Eveready 538)

The Kodak 110 film cameras, launched in 1972 came for an important part with a new battery size, the Kodak K or 7R31 type K battery. Other manufacturers followed and some of them adopted also the battery size. These batteries are no longer made and no longer available, even old stock is no solution any more. So these cameras have become useless. As 110 film is produced anew, this is a pity.

So how to replace a Kodak K or 7R31 type K battery? There are tutorials on the net which propose an external battery case. I found an easier solution, however it needs an old (even defective) battery, which you will find for next to nothing with old Kodak 110 cameras. The battery is also referred to as 7K31, Eveready 538 or RPX 31, it's 4.5 volt, also given as 4 volt. Sometimes you read that it's 4LR53, but I think this is wrong. LR53 is a bigger diameter and it's 3 cells, not 4.

This is what it looks like:

jpg/110_minolta_pocket_autopack_70_IMG_0101.JPG
A
 Kodak K battery, marketed under 7R31 type K, 7K31, Eveready Energizer 538 and RPX31. It has 4.5 volt.

You will need a Dremel or a similar tool, three V625U button cells, also named LR09, easily available, a middle sized screwdriver and 2 tiny sheets of metal, 15x4mm size. Disclaimer: do not try to do this unless you have basic DIY skills and if you understand what you do. You should understand basic electrics and short circuits.

jpg/110_replace_kodak_k_7r31_battery_IMG_0198.JPG
You have to cut the case open. Cut cautiously, do not cut into the battery cells and cut all round the case.

jpg/110_replace_kodak_k_7r31_battery_IMG_0199.JPG
Take a middle sized flat screwdriver, insert it into the freshly cut slit and break the case open.

jpg/110_replace_kodak_k_7r31_battery_IMG_0202.JPG
The case open. It's 3 button cells soldered together inside.

jpg/110_replace_kodak_k_7r31_battery_IMG_0205.JPG
Seen from above.

jpg/110_replace_kodak_k_7r31_battery_IMG_0203.JPG
One side...

jpg/110_replace_kodak_k_7r31_battery_IMG_0203.JPG
...and the other. The soldering of the 3rd cell (to the right) has to be pryed off. Insert a knife under the soldering lug and pry, it will come off.

jpg/110_replace_kodak_k_7r31_battery_IMG_0207.JPG
All disassembly done.

jpg/110_replace_kodak_k_7r31_battery_IMG_0210.JPG
Assembly cells, 3 different V625U cells and the old parts.

jpg/110_replace_kodak_k_7r31_battery_IMG_0212.JPG
The new cells put into the old case. They are nearly the same diameter, but about 0.5mm thicker than the old ones, so you have to force a bit.

jpg/110_replace_kodak_k_7r31_battery_IMG_0213.JPG
The new cells fit. They still have to be connected to each other.

jpg/110_replace_kodak_k_7r31_battery_IMG_0218.JPG
The 3rd cell in place. A small piece of metal, ca 15x4mm, to be inserted between 2 cells.

jpg/110_replace_kodak_k_7r31_battery_IMG_0219.JPG
Connection in place, I bent it a little bit to ensure a good connection to the next cell. Don't make it too long, it would touch the negative pole of the housing.

jpg/110_replace_kodak_k_7r31_battery_IMG_0220.JPG
Ready for the 1st cell. For the connection of the 3rd cell to the negative pole I just bent the old soldering lug against the cell.

jpg/110_replace_kodak_k_7r31_battery_IMG_0221.JPG
Assembly done, voltage test. If you want a bomb proof solution, solder the cells instead of just bending the connections. But it works well without soldering.

jpg/110_replace_kodak_k_7r31_battery_IMG_0215.JPG
The cell assembly put into the camera. No need to tape the two parts of the case together, they are held together on their own, once inserted.

So here you are with a fresh battery. Enjoy your camera!


back